Mikrotik Wifi Station Bridge

Обсуждение оборудования и его настройки
Аватара пользователя
podarok66
Модератор
Сообщения: 4355
Зарегистрирован: 11 фев 2012, 18:49
Откуда: МО

Значит не так настроили.


Мануалы изучил и нигде не ошибся? Фаервол отключил? Очереди погасил? Витая пара проверена? ... Тогда Netinstal'ом железку прошей и настрой ее заново. Что, все равно не фурычит? Тогда к нам. Если не подскажем, хоть посочувствуем...
Estranged
Сообщения: 4
Зарегистрирован: 29 июн 2018, 16:12

Настраивал строго по мануалу. Единственное, в мануале необходимо выбрать в настройках Микротика station bridge. При этом Микротик к сети Wi-Fi Зикселя цепляться вообще не хочет. При выборе station pseudobridge Микротик с сети Зикселя цепляется. Но IP получает 1 раз из 20. А вот судя по логам Зикселя, Зиксель выдает IP Микротику каждый раз.


sergey.nektov
Сообщения: 1
Зарегистрирован: 29 окт 2021, 12:55

По этой инструкции новая версия роутер-ОС работать не будет. Вот инфа от официалов
Mode station
This is standard mode that does not support L2 bridging on station - attempts to put wireless interface in bridge will not produce expected results. On the other hand this mode can be considered the most efficient and therefore should be used if L2 bridging on station is not necessary - as in case of routed or MPLS switched network. This mode is supported for all wireless protocols.
У Вас будет работать L2 уровень, даже будут раздаваться IP адреса, а вот пинг не пройдет.

Возможно использовать следующий режим
Mode station-pseudobridge
From the wireless connection point of view, this mode is the same as standard station mode. It has limited support for L2 bridging by means of some services implemented in station:

MAC address translation for IPv4 packets - station maintains IPv4-to-MAC mapping table and replaces source MAC address with its own address when sending frame to AP (in order to be able to use 3 address frame format), and replaces destination MAC address with address from mapping table for frames received from AP. IPv4-to-MAC mappings are built also for VLAN encapsulated frames.
single MAC address translation for the rest of protocols - station learns source MAC address from first forwarded non-IPv4 frame and uses it as default for reverse translation - this MAC address is used to replace destination MAC address for frames received from AP if IPv4-to-MAC mapping can not be performed (e.g. - non-IPv4 frame or missing mapping).
This mode is limited to complete L2 bridging of data to single device connected to station (by means of single MAC address translation) and some support for IPv4 frame bridging - bridging of non-IP protocols to more than one device will not work. Also MAC address translation limits access to station device from AP side to IPv4 based access - the rest of protocols will be translated by single MAC address translation and will not be received by station itself.

This mode is available for all protocols except nv2 and should be avoided when possible. The usage of this mode can only be justified if AP does not support better mode for L2 bridging (e.g. when non-RouterOS AP is used) or if only one end-user device must be connected to network by means of station device.
Но как пишут, он адекватно работает для одного клиента.
Мой совет. Подключайте микротик к точке доступа с помощью station и настраивайте маршрутизацию без обединения интерфейсов в бридж, с маскарадингом или протоколо динамической маршрутизации или настраивайте статическую маршрутизацию если точка доступа это поддерживает.


Ответить