RB951G-2HnD, прошивка 3.14, routeros 6.12.
после отключения питания, примерно, более чем на 5 минут стираются настройки. При включении питания, роутер не загрузается. Необходимо выполнять сброс при помощи кнопки и востанавливать настройки из резервной копии.
1. аптайм около 2 недель, за это время настройки не менялись.
2. отключил питание примерно минут на 10
3. включил питание, роутер пикнул 1 раз, помигал светодиодами и всё
4. светодиоды активности wlan и ethernet не горят, горит только индикатор питания PWR
5. в первые секунды заугрузки роутера, ethernet порты горят, компьютер с windows пытается индетифицироваться в сети, но затем на роутере будто отключаются все интерфейсы. windows пишет, что кабель не подключен.
6. перезагрузка роутера или отключение питания не помогает.
7. netinstall и winbox не видет роутер.
8. сбросил настройки при помощи кнопки RST, восстановил из резервной копии и всё заработало как и раньше
2. отключил питание примерно минут на 10
3. включил питание, роутер пикнул 1 раз, помигал светодиодами и всё
4. светодиоды активности wlan и ethernet не горят, горит только индикатор питания PWR
5. в первые секунды заугрузки роутера, ethernet порты горят, компьютер с windows пытается индетифицироваться в сети, но затем на роутере будто отключаются все интерфейсы. windows пишет, что кабель не подключен.
6. перезагрузка роутера или отключение питания не помогает.
7. netinstall и winbox не видет роутер.
8. сбросил настройки при помощи кнопки RST, восстановил из резервной копии и всё заработало как и раньше
[mons@MikroTik] > export compact
# may/07/2014 10:55:38 by RouterOS 6.12
# software id = SE2X-0TRW
#
/interface bridge
add admin-mac=****** auto-mac=no l2mtu=1598 name=bridge-local
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n basic-rates-a/g=\
6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps basic-rates-b=\
1Mbps,2Mbps,5.5Mbps,11Mbps country=russia disabled=no distance=indoors \
frequency=2457 hw-protection-mode=rts-cts l2mtu=2290 mode=ap-bridge \
periodic-calibration=enabled periodic-calibration-interval=30 ssid=****** \
tx-power=23 tx-power-mode=all-rates-fixed wireless-protocol=802.11
/interface ethernet
set [ find default-name=ether1 ] name=ether1-gateway
set [ find default-name=ether2 ] name=ether2-master-local
set [ find default-name=ether3 ] master-port=ether2-master-local name=\
ether3-slave-local
set [ find default-name=ether4 ] master-port=ether2-master-local name=\
ether4-slave-local
set [ find default-name=ether5 ] master-port=ether2-master-local name=\
ether5-slave-local
/ip neighbor discovery
set wlan1 discover=no
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk mode=dynamic-keys \
wpa-pre-shared-key=****** wpa2-pre-shared-key=******
add authentication-types=wpa-psk,wpa2-psk eap-methods="" \
management-protection=allowed name=for_virual_AP_free \
supplicant-identity=""
/interface wireless
add default-forwarding=no disabled=no l2mtu=2290 mac-address=\
****** master-interface=wlan1 name=wlan2 security-profile=\
for_virual_AP_free ssid=****** wds-cost-range=0 wds-default-cost=\
0
/ip neighbor discovery
set wlan2 discover=no
/ip hotspot user profile
set [ find default=yes ] idle-timeout=none keepalive-timeout=2m \
mac-cookie-timeout=3d
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=3des
/ip pool
add name=default-dhcp ranges=192.168.88.10-192.168.88.30
add name=dhcp_pool1 ranges=192.168.80.2-192.168.80.254
/ip dhcp-server
add address-pool=default-dhcp disabled=no interface=bridge-local name=default
add address-pool=dhcp_pool1 disabled=no interface=wlan2 name=dhcp1
/interface ovpn-client
add add-default-route=no auth=sha1 certificate=cert_2 cipher=blowfish128 \
connect-to=****** disabled=no mac-address=***** max-mtu=\
1500 mode=ip name=ovpn-out1 password="" port=***** profile=default user=\
mons
/interface pppoe-client
add ac-name="" add-default-route=yes allow=pap,chap,mschap1,mschap2 \
default-route-distance=1 dial-on-demand=no disabled=no interface=\
ether1-gateway keepalive-timeout=60 max-mru=1480 max-mtu=1480 mrru=\
disabled name=pppoe-out1 password=**** profile=default \
service-name="" use-peer-dns=yes user=****
/ip neighbor discovery
set pppoe-out1 discover=no
/queue simple
add max-limit=5M/5M name="for Virtual AP" target=192.168.80.0/24
/system logging action
set 0 memory-lines=100
set 1 disk-lines-per-file=20000
set 3 remote=192.168.88.12 src-address=192.168.88.1
/interface bridge port
add bridge=bridge-local interface=ether2-master-local
add bridge=bridge-local interface=wlan1
/interface pptp-server server
set max-mru=1460 max-mtu=1460
/ip address
add address=192.168.88.1/24 comment="default configuration" interface=wlan1 \
network=192.168.88.0
add address=192.168.80.1/24 interface=wlan2 network=192.168.80.0
/ip dhcp-client
add comment="default configuration" dhcp-options=hostname,clientid interface=\
ether1-gateway
/ip dhcp-server network
add address=192.168.80.0/24 dns-server=77.88.8.7,77.88.8.3 gateway=\
192.168.80.1
add address=192.168.88.0/24 comment="default configuration" dns-server=\
8.8.8.8,8.8.4.4 gateway=192.168.88.1 netmask=24
/ip dns
set allow-remote-requests=yes servers=8.8.8.8,212.120.173.34
/ip dns static
add address=192.168.88.1 name=router
/ip firewall filter
add chain=input comment="default configuration" protocol=icmp
add chain=input comment="default configuration" connection-state=established
add chain=input comment="default configuration" connection-state=related
add chain=forward comment="default configuration" connection-state=\
established
add chain=forward comment="default configuration" connection-state=related
add action=drop chain=input comment="default configuration" in-interface=\
ether1-gateway
add action=drop chain=forward comment="default configuration" \
connection-state=invalid
add action=drop chain=input comment="\EE\E3\F0\E0\ED\E8\F7\E5\ED\E8\E5 \E4\EE\
\F1\F2\F3\EF\E0 \EA 192.168.80.1 \E8\E7 virtual AP \E4\EB\FF \E2\F1\E5\F5 \
\E0\E4\F0\E5\F1\EE\E2" dst-address=192.168.80.1
/ip firewall mangle
add action=mark-routing chain=prerouting dst-port=80,81,8080,9050 \
new-routing-mark=vpn_digitalocean protocol=tcp src-address=\
192.168.88.1-192.168.88.254
/ip firewall nat
add action=masquerade chain=srcnat out-interface=pppoe-out1
add action=masquerade chain=srcnat out-interface=ovpn-out1
/ip proxy
set cache-administrator="" cache-hit-dscp=0 max-fresh-time=0s parent-proxy=\
0.0.0.0
/ip route
add distance=1 gateway=ovpn-out1 routing-mark=vpn_digitalocean
/ip route rule
add action=unreachable dst-address=192.168.88.0/24 src-address=\
192.168.80.0/24
add action=unreachable dst-address=192.168.80.0/24 src-address=\
192.168.88.0/24
/ip service
set telnet disabled=yes
set ftp disabled=yes
set www address=192.168.88.0/24
set ssh address=192.168.88.0/24
set api disabled=yes
set winbox address=192.168.88.0/24
/ip smb
set allow-guests=no comment=SMB interfaces=bridge-local
/ip smb shares
add directory=/ name=share1
/ip upnp
set enabled=yes
/ip upnp interfaces
add interface=bridge-local type=internal
add interface=ether1-gateway type=external
/system clock manual
set time-zone=+06:00
/system leds
set 0 interface=wlan1
/system logging
set 0 action=disk
set 1 action=disk
set 2 action=disk
set 3 action=disk
add action=disk topics=pppoe
/system ntp client
set enabled=yes primary-ntp=139.143.5.30 secondary-ntp=178.33.43.248
/system scheduler
add interval=1d name=reconnect on-event="/interface disable pppoe-out1\r\
\ndelay 5\r\
\n/interface disable ether1-gateway\r\
\ndelay 30\r\
\n/interface enable ether1-gateway\r\
\n/delay 5\r\
\n/interface enable pppoe-out1" policy=\
ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api \
start-date=apr/20/2014 start-time=04:00:00
/tool graphing interface
add
/tool graphing resource
add
/tool mac-server
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
/tool mac-server mac-winbox
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
/tool sniffer
set filter-stream=yes
# may/07/2014 10:55:38 by RouterOS 6.12
# software id = SE2X-0TRW
#
/interface bridge
add admin-mac=****** auto-mac=no l2mtu=1598 name=bridge-local
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n basic-rates-a/g=\
6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps basic-rates-b=\
1Mbps,2Mbps,5.5Mbps,11Mbps country=russia disabled=no distance=indoors \
frequency=2457 hw-protection-mode=rts-cts l2mtu=2290 mode=ap-bridge \
periodic-calibration=enabled periodic-calibration-interval=30 ssid=****** \
tx-power=23 tx-power-mode=all-rates-fixed wireless-protocol=802.11
/interface ethernet
set [ find default-name=ether1 ] name=ether1-gateway
set [ find default-name=ether2 ] name=ether2-master-local
set [ find default-name=ether3 ] master-port=ether2-master-local name=\
ether3-slave-local
set [ find default-name=ether4 ] master-port=ether2-master-local name=\
ether4-slave-local
set [ find default-name=ether5 ] master-port=ether2-master-local name=\
ether5-slave-local
/ip neighbor discovery
set wlan1 discover=no
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk mode=dynamic-keys \
wpa-pre-shared-key=****** wpa2-pre-shared-key=******
add authentication-types=wpa-psk,wpa2-psk eap-methods="" \
management-protection=allowed name=for_virual_AP_free \
supplicant-identity=""
/interface wireless
add default-forwarding=no disabled=no l2mtu=2290 mac-address=\
****** master-interface=wlan1 name=wlan2 security-profile=\
for_virual_AP_free ssid=****** wds-cost-range=0 wds-default-cost=\
0
/ip neighbor discovery
set wlan2 discover=no
/ip hotspot user profile
set [ find default=yes ] idle-timeout=none keepalive-timeout=2m \
mac-cookie-timeout=3d
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=3des
/ip pool
add name=default-dhcp ranges=192.168.88.10-192.168.88.30
add name=dhcp_pool1 ranges=192.168.80.2-192.168.80.254
/ip dhcp-server
add address-pool=default-dhcp disabled=no interface=bridge-local name=default
add address-pool=dhcp_pool1 disabled=no interface=wlan2 name=dhcp1
/interface ovpn-client
add add-default-route=no auth=sha1 certificate=cert_2 cipher=blowfish128 \
connect-to=****** disabled=no mac-address=***** max-mtu=\
1500 mode=ip name=ovpn-out1 password="" port=***** profile=default user=\
mons
/interface pppoe-client
add ac-name="" add-default-route=yes allow=pap,chap,mschap1,mschap2 \
default-route-distance=1 dial-on-demand=no disabled=no interface=\
ether1-gateway keepalive-timeout=60 max-mru=1480 max-mtu=1480 mrru=\
disabled name=pppoe-out1 password=**** profile=default \
service-name="" use-peer-dns=yes user=****
/ip neighbor discovery
set pppoe-out1 discover=no
/queue simple
add max-limit=5M/5M name="for Virtual AP" target=192.168.80.0/24
/system logging action
set 0 memory-lines=100
set 1 disk-lines-per-file=20000
set 3 remote=192.168.88.12 src-address=192.168.88.1
/interface bridge port
add bridge=bridge-local interface=ether2-master-local
add bridge=bridge-local interface=wlan1
/interface pptp-server server
set max-mru=1460 max-mtu=1460
/ip address
add address=192.168.88.1/24 comment="default configuration" interface=wlan1 \
network=192.168.88.0
add address=192.168.80.1/24 interface=wlan2 network=192.168.80.0
/ip dhcp-client
add comment="default configuration" dhcp-options=hostname,clientid interface=\
ether1-gateway
/ip dhcp-server network
add address=192.168.80.0/24 dns-server=77.88.8.7,77.88.8.3 gateway=\
192.168.80.1
add address=192.168.88.0/24 comment="default configuration" dns-server=\
8.8.8.8,8.8.4.4 gateway=192.168.88.1 netmask=24
/ip dns
set allow-remote-requests=yes servers=8.8.8.8,212.120.173.34
/ip dns static
add address=192.168.88.1 name=router
/ip firewall filter
add chain=input comment="default configuration" protocol=icmp
add chain=input comment="default configuration" connection-state=established
add chain=input comment="default configuration" connection-state=related
add chain=forward comment="default configuration" connection-state=\
established
add chain=forward comment="default configuration" connection-state=related
add action=drop chain=input comment="default configuration" in-interface=\
ether1-gateway
add action=drop chain=forward comment="default configuration" \
connection-state=invalid
add action=drop chain=input comment="\EE\E3\F0\E0\ED\E8\F7\E5\ED\E8\E5 \E4\EE\
\F1\F2\F3\EF\E0 \EA 192.168.80.1 \E8\E7 virtual AP \E4\EB\FF \E2\F1\E5\F5 \
\E0\E4\F0\E5\F1\EE\E2" dst-address=192.168.80.1
/ip firewall mangle
add action=mark-routing chain=prerouting dst-port=80,81,8080,9050 \
new-routing-mark=vpn_digitalocean protocol=tcp src-address=\
192.168.88.1-192.168.88.254
/ip firewall nat
add action=masquerade chain=srcnat out-interface=pppoe-out1
add action=masquerade chain=srcnat out-interface=ovpn-out1
/ip proxy
set cache-administrator="" cache-hit-dscp=0 max-fresh-time=0s parent-proxy=\
0.0.0.0
/ip route
add distance=1 gateway=ovpn-out1 routing-mark=vpn_digitalocean
/ip route rule
add action=unreachable dst-address=192.168.88.0/24 src-address=\
192.168.80.0/24
add action=unreachable dst-address=192.168.80.0/24 src-address=\
192.168.88.0/24
/ip service
set telnet disabled=yes
set ftp disabled=yes
set www address=192.168.88.0/24
set ssh address=192.168.88.0/24
set api disabled=yes
set winbox address=192.168.88.0/24
/ip smb
set allow-guests=no comment=SMB interfaces=bridge-local
/ip smb shares
add directory=/ name=share1
/ip upnp
set enabled=yes
/ip upnp interfaces
add interface=bridge-local type=internal
add interface=ether1-gateway type=external
/system clock manual
set time-zone=+06:00
/system leds
set 0 interface=wlan1
/system logging
set 0 action=disk
set 1 action=disk
set 2 action=disk
set 3 action=disk
add action=disk topics=pppoe
/system ntp client
set enabled=yes primary-ntp=139.143.5.30 secondary-ntp=178.33.43.248
/system scheduler
add interval=1d name=reconnect on-event="/interface disable pppoe-out1\r\
\ndelay 5\r\
\n/interface disable ether1-gateway\r\
\ndelay 30\r\
\n/interface enable ether1-gateway\r\
\n/delay 5\r\
\n/interface enable pppoe-out1" policy=\
ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api \
start-date=apr/20/2014 start-time=04:00:00
/tool graphing interface
add
/tool graphing resource
add
/tool mac-server
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
/tool mac-server mac-winbox
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
/tool sniffer
set filter-stream=yes